Tune your bike to the limit with our advanced ECU Flashing Products for Kawasaki, Honda, Suzuki, BMW, Ducati and Yamaha motorcycles.
Woolich Racing - Tune your bike to the limit
CONTACT US

User Support->On Bike Harnesses

Type 3 wiring harness

 Re: Type 3 wiring harness
Just to add a bit more I'm connecting to a ecueditor interface and the molex connector. The pins are as follows (looking at the insert side) Ground sensor - rxd - k line sds - 12 volt Reset - txd - empty - mod
 
 Re: Type 3 wiring harness
I think all computes from my side, but one last question re the type 3 harness, the ecueditor wiring used pin 25 reset, it has no wire in the plug so can you confirm I don't need it. On a related point does the bench harness uses the same pins on both the molex and ecu end. Thanks
 
 Re: Type 3 wiring harness
So have checked and rechecked all wiring according to these diagrams but still cannot talk to the bike. Keep getting error messages about unexpected response.
 
 Re: Type 3 wiring harness
No its like this :) now my head hurts ha ha Molex 3 = SDS 2 Molex 4 = Yosh 1 Molex 5 = SDS 1 Molex 6 = SDS 5 Molex 7 = SDS 4 Molex 8 = SDS 6
 
 Re: Type 3 wiring harness
Makes it a bit clearer in my head now, so to summaries SDS Plug SDS Pin 1 = Molex Pin 5 SDS Pin 5 = Molex Pin 6 SDS Pin 6 = Molex Pin 8 Yosh Plug Yosh Pin 1 = Molex Pin 1 Yosh Pin 3 = Molex Pin 3 Yosh Pin 4 = Molex Pin 4 Yosh Pin 5 = Molex Pin 7 My head hurts :roll: Thanks
 
 Re: Type 3 wiring harness
http://imageshack.us/a/img708/4448/sdsandyosh.png http://imageshack.us/a/img835/3807/84679196.png hope this helps
 
 Re: Type 3 wiring harness
Is it possible to post pictures of the connectors so I can tie up your numbers to the postions in the 3 plugs. Thanks, as the say a picture says a thousand stories.
 
 Re: Type 3 wiring harness
Hi Below is the wiring for the type 2/3 main harness Molex - SDS - Yosh 1 2 3 -------- 2 4 -----------------1 5 ---------1 6 -------- 5 7 ---------4 8 ---------6
 
 Re: Type 3 wiring harness
Any chance of the wiring config to assist?
 
 Re: Type 3 wiring harness
On my third computer and second log box on this GSXR 600 I am trying to tune, have the harness and jumper wire installed as per instructions and cannot connect no matter what I try. Where to now?
 
 Type 3 wiring harness
Is it possible that you could detail down the wires from the Molex connector to their respective either Yosh or SDS connector and onto the ecu pins for type 3, so that I can confirm that my lead is wired up correctly. Thanks (Moved from GSR 600 INSTALL thread)
 
 
View Topic on the Woolich Racing Forums
 
OUR PRODUCTS SUPPORT OUR COMPANY  
Suzuki ECU Flashing
Kawasaki ECU Flashing
Honda ECU Flashing
Yamaha ECU Flashing
BMW ECU Flashing
Ducati ECU Flashing
Woolich Racing Merchandise
What Harness for Bike?
What Bike uses Harness?
Woolich Racing Tuned (WRT) software
Woolich Racing MapShare
USB D (Denso)
Log Box D (Denso)
Log Box Pro D (Denso)
USB M (Mitsubishi)
Log Box M (Mitsubishi)
Log Box Pro M (Mitsubishi)
Zeitronix Wideband O2 Products
Tuning Shops and Dealers
Support Center
Support Tickets
Video Tutorials
User Guides and Installation Instructions
COM Port Drivers
Software Release Notes
User Support
Contact Us
About Us
Official Technical Partner WorldSBK
Electronic Mapping - Plug and Play Performance
Woolich Racing News
Testimonials
Terms and Conditions
Privacy Policy
Mobile Site
Woolich Racing page on facebook
Woolich Racing on YouTube.com
Woolich Racing Products are Intended for RACE USE on CLOSED CIRCUIT ONLY

© Woolich Racing and www.WoolichRacing.com, 2011-2021. Unauthorized use or duplication of any of the material on this website without express and written permission from this website’s author and owner is strictly prohibited. Excerpts and links may be used, provided that full and clear credit is given to Woolich Racing and www.WoolichRacing.com with appropriate and specific direction to the original content.