Tune your bike to the limit with our advanced ECU Flashing Products for Kawasaki, Honda, Suzuki, Ducati and Yamaha motorcycles.
Woolich Racing - Tune your bike to the limit

User Support->ECU Reading and Writing (Flashing) Issues

Unexpected or missing ECU on 750 GSXR 09

 Re: Unexpected or missing ECU on 750 GSXR 09
here is the link to the tests for anyone looking for them: http://www.woolichracing.com/SupportCenter/Item/64/testing-the-usb-interface-denso-log-box-denso.aspx Contact us with a support ticket if you are having problems with something like this: http://www.woolichracing.com/support/open.php
 Re: Unexpected or missing ECU on 750 GSXR 09
If you are not getting 4.5v + between pins 1 and 8 and pins 4 and 8 this would be the problem.
 Re: Unexpected or missing ECU on 750 GSXR 09
I ran into this today. Everything checked out except the voltage between 4-8 was 1.98 v. I have no problem modifying maps and options and saving them to be flashed with ecueditor. But the wrt software will not read or write. I submitted a ticket but was just wondering if anyone knew the next step. I know it may take a few day to receive a response and I'm ok with that. But I'm extremely anxious to begin tuning my bike. I run a gen II Busa ecu on my '03 turbo 1000 and its race season! :D
 Re: Unexpected or missing ECU on 750 GSXR 09
HI I dont think this is related to the immobilizer at all. If you are not getting the required voltages for the voltage tests then there may be a problem with the interface, Can you please Contact Us and we will get the problem resolved for you.
 Unexpected or missing ECU on 750 GSXR 09
hello, I just bought a module woolich I have a EU model bike and my ECU is a 38H30 the mentioned software is "restricted" when I followed the advise of connection it myself an error message Unexpected or missing ECU response falling on intialization. "Please turn Ignition Off Then On again, Reset Interface and try again" I performed the following tests: -Test Mode Flashing is OK -I also perform a test harness the molex plug has ECU is OK -Measure the voltage Between pin 4 and pin 8 on the interface, this 4.5-5v shoulds be NOK my voltage is 2.10V? -Measure the voltage Between pin 1 and pin 8 on the interface, this shoulds be 4.5-5v When in flash mode (red LED on) NOK my voltage is 1.80v? or it may come from? I can not seem to connect to the ecu I want to clarify that this model works with a immobizer I replace my 600 engine with a 750 I 750 ECU immobilizer But not to go with the engine Were sold without ... to be able to write an unrestricted map you need it as I pass by a bench harness to you because I have the impression that ECU did not allimenter because of the securiter? thank you all in advance for your help! :P
View Topic on the Woolich Racing Forums
Suzuki ECU Flashing
Kawasaki ECU Flashing
Honda ECU Flashing
Yamaha ECU Flashing
Ducati ECU Flashing
Woolich Racing Merchandise
What Harness for Bike?
What Bike uses Harness?
Woolich Racing Tuned (WRT) software
Woolich Racing MapShare
USB D (Denso)
Log Box D (Denso)
Log Box Pro D (Denso)
USB M (Mitsubishi)
Log Box M (Mitsubishi)
Log Box Pro M (Mitsubishi)
Zeitronix Wideband O2 Products
Tuning Shops and Dealers
Support Center
Support Tickets
Video Tutorials
User Guides and Installation Instructions
COM Port Drivers
Software Release Notes
User Support
Contact Us
About Us
Official Technical Partner WorldSBK
Electronic Mapping - Plug and Play Performance
Woolich Racing News
Terms and Conditions
Privacy Policy
Mobile Site
Woolich Racing page on facebook
Woolich Racing on YouTube.com
Woolich Racing Products are Intended for RACE USE on CLOSED CIRCUIT ONLY

© Woolich Racing and www.WoolichRacing.com, 2011-2020. Unauthorized use or duplication of any of the material on this website without express and written permission from this website’s author and owner is strictly prohibited. Excerpts and links may be used, provided that full and clear credit is given to Woolich Racing and www.WoolichRacing.com with appropriate and specific direction to the original content.