Woolich Racing Products

• Log Box (D-Can) v3
• USB Cable
• On board 4GB micro SD card
• Kawasaki Bench Harness Type 22
• Universal Harness Type 3 (engine data)
  
• Bin File Definitions in Woolich Racing Tuned Software
• 
  

• Log Box (D-can) v3
• USB Cable
• On board 4GB micro SD card
• Kawasaki Bench Harness Type 22
• Universal Harness Type 3 (engine data only)
  
• Bin File Definitions in Woolich Racing Tuned Software
• Zeitronix ZT-3 Wideband O2 Controller
• Zeitronix Wideband O2 Sensor (3 foot cable)
• RJ12 cable to connect Zeitronix to Log Box
• Zeitronix Installation Kit
• O2 sensor bung

• Log Box (Denso) v3
• USB Cable
• On board 4GB micro SD card
• Kawasaki Bench Harness Type 22
• Universal Harness Type 2
  
• Bin File Definitions in Woolich Racing Tuned Software

The Race Tools package allows you to enable Quickshifter, Launch Control and Pit Speed Limiter in the Stock ECU.

The package includes:

• High quality strain gauge Quickshifter with digitally controlled pressure sensing that can be used in regular or race shift pattern.
• Shift rod for standard shift configuration*
• Kawasaki Race Tools Harness Type 11 which allows the quickshifter to be plugged into the bikes wiring harness**
• Race Tools Key to allow the use of the Race Tools on one ECU in the Woolich Racing Tuned software.

This product only currently works with part numbers 21175-1688 to 21175-1693

Quickshifter Kill times are configurable per gear with 3D maps allowing Kill Times to be set for the full range of TPS and RPM combinations. The quickshifter kills ignition.

Launch Control allows you to configure Delay, Launch RPM, Ramp Time and Ramp RPM

Pit Speed Limiter allows you to set the RPM to limit the speed while riding through the pits.***

* Contact us after ordering if you have after-market rearsets or are using a race shift pattern and we will swap the shift rod for a generic rod that can be cut and tapped to the correct length.

** This harness uses the stock O2 Sensor plug on the bike's harness, the stock O2 sensor should be removed from the bike and disabled in our software

*** Pit Speed Limiter harness sold separately

• IAP Fuel Maps
• TPS Fuel Maps
• Ignition Timing Maps
• Ignition Dwell Map/s
• Secondary Throttle Plate (STP) Opening Maps
• Fan Temperature
• Disable Stock O2 Sensor
• Disable Deceleration Fuel Cut
• Disable PAIR Valve / AIS
• ECU Mode
• Engine Data - View Live Engine Data
• Woolich Racing AutoTune - (Requires Applicable LogBox + Zeitronix Package)
• Diagnostics: Read and Clear Fault Codes - (Requires Applicable V3 Interface)

• 21175-1588 KPN7K8E0
• 21175-1688 KPL7K8J0
• 21175-1689 KPL7K8U0
• 21175-1690 KPL7K8L0
• 21175-1691 KPL7K8D0
• 21175-1693 KPL7K8M0
• 21175-1706 TPP2K8J0
• 21175-1840 TPP2K8E0
• 21175-1841 TPP2K8S0

• Twin RJ12 cable to connect Zeitronix to Log Box
• Ducati Power Harness 1 & 2
• x O2 Stainless Steel Bung
• Adhesive Velcro for attaching ZT-3 to bike.

• Twin RJ12 cable to connect Zeitronix to Log Box
• Ducati  Power Harness 1 & 2
• 2  x O2 TITANIUM Bungs
  
• Adhesive Velcro for attaching ZT-3 to bike.

• RJ12 cable for connecting ZT-3 to Woolich Racing Products
• Kawasaki Power Harness Type 1
• O2 Stainless Steel Bung
  
• Adhesive Velcro for attaching ZT-3 to bike.

• RJ12 cable for connecting ZT-3 to Woolich Racing Products
• Kawasaki Power Harnes Type 2
  
• O2 Stainless Steel Bung
  
• Adhesive Velcro for attaching ZT-3 to bike.

• RJ12 cable for connecting ZT-4 to Woolich Racing Products
• KTM Power Harness Type 1
• 2 x O2 Stainless Steel Bung
  
• Adhesive Velcro for attaching ZT-4 to bike.

• RJ12 cable for connecting ZT-3 to Woolich Racing Products
• Suzuki Power Harness
  
• O2 Stainless Steel Bung
  
• Adhesive Velcro for attaching ZT-3 to bike.

• Wideband O2 sensor bung (stainless Steel)
  
• Wideband O2 sensor bung (Titanium)
• Tuning Shop Power Harness (type 1)
  
• RJ12 cables for connecting ZT-3 to Woolich Racing Products - 1 x small, 1 x large
  
• 2 x Narrow band bungs
  

• RJ12 cable for connecting ZT-3 to Woolich Racing Products
• Yamaha Power Harness
  
• O2 Stainless Steel Bung
  
• Adhesive Velcro for attaching ZT-3 to bike.

• Stylish, machined, anodized black bezel and slim enclosure
• High contrast Blue LED display
• Large 0.4" (10mm) digits
• Slim design for flexible gauge mounting options
• Programmable to startup as an AFR or Lambda gauge
• Peak and Hold feature
• RJ12 Splitter cable included

• Stylish, machined, anodized black bezel and slim enclosure
• High contrast Red LED display
• Large 0.4" (10mm) digits
• Slim design for flexible gauge mounting options
• Programmable to startup as an AFR or Lambda gauge
• Peak and Hold feature
• RJ12 Splitter cable included

• Blue digital AFR readout with large 0.4" (10mm) digits
• Slim 0.75" (19mm) design
• High contrast display visible even in direct sunlight
• RJ12 Splitter cable included

• Red digital AFR readout with large 0.4" (10mm) digits
• Slim 0.75" (19mm) design
• High contrast display visible even in direct sunlight
• RJ12 Splitter cable included