Tune your bike to the limit with our advanced ECU Flashing Products for Kawasaki, Honda, Suzuki, BMW, Ducati, Harley Davidson, Triumph and Yamaha motorcycles.
Woolich Racing - Tune your bike to the limit
Login  - 

Engine Data logging settings

The Woolich Racing Log Box products allow data to be written (logged) to an micro-SD card while the bike is being run on the street, track or dyno.  The Log Box will typically start logging data whenever the ignition is started AND the device is NOT connected to the computer.  

The exact settings about how the data logging works can be modified by the user in the Woolich Racing Tuned software on the computer.  These settings can be viewed by connecting the Log Box to your PC and setting your Log Start Configuration which can be found under Tools > Device Configuration Page as shown below.

Open the Device Configuration from the Tools menu in the Woolich Racing Tuned software

The Log Start Configuration is shown as in the screenshot below:

The Default "Log Start Configuration" settings are:

Time Delay (secs) = 0
 - The number of seconds to delay before starting to log data after the device is powered on. This setting is useful if you would like to delay data logging to prevent log files from being created when starting the bike for short amounts of time.  

Engine Running = not ticked
 - When this option is checked the engine must be running before data will be logged. This setting is useful to prevent logging data when the key is turned on but the engine is not running.

RPM = 0
 - The RPM that the engine must go above before data logging will begin. This setting is useful to delay the start of data logging until the engine has been taken above the selected RPM. 

Log data to micro-SD in Engine data Mode = not ticked.
 - This setting creates data logs on the Interface when in normal operation mode. It is useful if you are using the Interface on the dyno to monitor engine data and you would also like to log data to be used with the Woolich Racing AutoTune.

OBD2 Engine data = not ticked
 - This option is required for models that use OBD2 engine data protocol. You can see it your model requires OBD2 data by checking the Engine Data Type' in the Bin File Details. If your model shows the Engine Data type: "OBD2 - CAN", then you will need to tick this option, and save to the Log Box.

For more information please view the Engine Data Types and Setup Support Center article. 

CAN Logging = not ticked
 - This is a troubleshooting option that you may be asked to use by the Woolich Racing Support Team. Please do not tick this option unless asked to by one of our Support Technicians.

After making changes to the the Start Log Configuration, be sure to click the Save button so that the settings are written to the Log Box.

If all options set to 0 or unticked, the Log Box will start recording data as soon as power is supplied (ie. when the key is turned).

After the Log Start Configuration has been set, you can disconnect the Log Box from your PC, and connect it to your Bike harness. You should then start the bike engine, and check the LEDs on the Log Box - the green and orange LEDs should flash quickly, and the red one should flash briefly every few seconds. This indicates the Log Box is receiving data, and recording it to the micro-SD Card.

Was this helpful?
Back To Support Center

Suzuki ECU Flashing
Kawasaki ECU Flashing
Honda ECU Flashing
Yamaha ECU Flashing
BMW ECU Flashing
Ducati ECU Flashing
Harley Davidson ECU Flashing
Triumph ECU Flashing
Woolich Racing Merchandise
What Harness for Bike?
What Bike uses Harness?
Woolich Racing Tuned (WRT) software
Woolich Racing MapShare
USB D (Denso)
Log Box D (Denso)
USB M (Mitsubishi)
Log Box M (Mitsubishi)
Zeitronix Wideband O2 Products
Tuning Shops and Dealers
Support Center
Support Tickets
Video Tutorials
User Guides and Installation Instructions
Dyno Tuning Motorcycles
Bikes Required for Development
COM Port Drivers
Software Release Notes
User Support
Contact Us
About Us
Official Technical Partner WorldSBK
Electronic Mapping - Plug and Play Performance
Woolich Racing News
Terms and Conditions
Privacy Policy
Mobile Site
Woolich Racing page on facebook
Woolich Racing on YouTube.com
Woolich Racing Products are Intended for RACE USE on CLOSED CIRCUIT ONLY

© Woolich Racing and www.WoolichRacing.com, 2011-2024. Unauthorized use or duplication of any of the material on this website without express and written permission from this website’s author and owner is strictly prohibited. Excerpts and links may be used, provided that full and clear credit is given to Woolich Racing and www.WoolichRacing.com with appropriate and specific direction to the original content.