Woolich Racing Products

• USB (Denso) v3
• Yamaha Harness Type 4
• USB Cable
• Bin File Definitions in the Woolich Racing Tuned software

The Race Tools package allows you to add Autoblipper, Quickshifter, Pit Speed Limiter, Engine Warm Up and Launch Control to the Stock R6 ECU.

The package includes:

• High quality dual direction strain gauge Quickshifter with digitally controlled pressure sensing that can be used in regular or race shift pattern.
• Shift rod for standard shift configuration*
• Yamaha Race Tools Type 1 which allows the quickshifter to be plugged into the bikes wiring harness**
• Race Tools Key to allow the use of the Race Tools on one ECU in the Woolich Racing Tuned software.

Quickshifter Kill times are configurable per gear with 3D maps allowing Kill Times to be set for the full range of TPS and RPM combinations. 

Autoblipper Opening and Duration maps are fully configurable per gear.

Launch Control allows you to configure Delay, Launch RPM and Hold Speed.

Pit Speed Limiter RPM can be configured.***

Engine Warm Up parameters are configurable.***

* Contact us after ordering if you have after-market rearsets or are using a race shift pattern and we will swap the shift rod for a generic rod that can be cut and tapped to the correct length.

** This harness uses the stock exhaust valve plugs on the bike's harness, the stock exhaust valve should be removed from the bike and disabled in the WRT software

*** The Pit Speed Limiter / Engine Warm Up requires the purchase of an additional Pit Speed Limiter harness

• IAP Fuel Maps
• TPS Fuel Maps
• Ignition Timing Maps
• Ignition Dwell Map/s
• Electronic Throttle Valve (ETV) Maps
• Electronic Throttle Valve Deceleration Maps
• Coolant Temp Idle Compensation
• Acceleration Enrichment
• Injector Balance Map/s
• Injector Timing Map/s
• Exhaust Valve Opening Maps
• RPM Limiter
• Fan Temperature
• Quickshifter - (Requires Race Tools)
• Autoblipper - (Requires Race Tools)
• Launch Control - (Requires Race Tools)
• Pit Lane Limiter - (Requires Race Tools)
• Engine Warm Up - (Requires Race Tools)
• Race Shift Pattern Sensor Configuration - (Requires Race Tools)
• Disable Stock O2 Sensor
• Disable Deceleration Fuel Cut
• Disable Exhaust Valve
• Disable PAIR Valve / AIS
• YCCI Opening / Closing
• ECU Mode
• Firing Order EU / US
• Engine Data - View Live Engine Data
• Woolich Racing AutoTune Live - Dyno Use Only - (Requires Applicable LogBox + Zeitronix Package)

• 13S-8591A-00
• 13S-8591A-00 01
• 13S-8591A-00 02
• 13S-8591A-10
• 13S-8591A-10 01
• 13S-8591A-10 02
• 13S-8591A-20
• 13S-8591A-20 01
• 13S-8591A-20 02
• 13S-8591A-30
• 13S-8591A-40
• 13S-8591A-40 01
• 13S-8591A-40 02
• 13S-8591A-50
• 13S-8591A-60
• 13S-8591A-60 01
• 13S-8591A-60 02
• 13S-8591A-A0
• 13S-8591A-B0
• 13S-8591A-C0
• 13S-8591A-D0
• 13S-8591A-D0 01
• 13S-8591A-D0 02
• 13S-8591A-E0

• Twin RJ12 cable to connect Zeitronix to Log Box
• Ducati Power Harness 1 & 2
• x O2 Stainless Steel Bung
• Adhesive Velcro for attaching ZT-3 to bike.

• Twin RJ12 cable to connect Zeitronix to Log Box
• Ducati  Power Harness 1 & 2
• 2  x O2 TITANIUM Bungs
  
• Adhesive Velcro for attaching ZT-3 to bike.

• RJ12 cable for connecting ZT-3 to Woolich Racing Products
• Kawasaki Power Harness Type 1
• O2 Stainless Steel Bung
  
• Adhesive Velcro for attaching ZT-3 to bike.

• RJ12 cable for connecting ZT-3 to Woolich Racing Products
• Kawasaki Power Harnes Type 2
  
• O2 Stainless Steel Bung
  
• Adhesive Velcro for attaching ZT-3 to bike.

• RJ12 cable for connecting ZT-4 to Woolich Racing Products
• KTM Power Harness Type 1
• 2 x O2 Stainless Steel Bung
  
• Adhesive Velcro for attaching ZT-4 to bike.

• RJ12 cable for connecting ZT-3 to Woolich Racing Products
• Suzuki Power Harness
  
• O2 Stainless Steel Bung
  
• Adhesive Velcro for attaching ZT-3 to bike.

• Wideband O2 sensor bung (stainless Steel)
  
• Wideband O2 sensor bung (Titanium)
• Tuning Shop Power Harness (type 1)
  
• RJ12 cables for connecting ZT-3 to Woolich Racing Products - 1 x small, 1 x large
  
• 2 x Narrow band bungs
  

• RJ12 cable for connecting ZT-3 to Woolich Racing Products
• Yamaha Power Harness
  
• O2 Stainless Steel Bung
  
• Adhesive Velcro for attaching ZT-3 to bike.

• Stylish, machined, anodized black bezel and slim enclosure
• High contrast Blue LED display
• Large 0.4" (10mm) digits
• Slim design for flexible gauge mounting options
• Programmable to startup as an AFR or Lambda gauge
• Peak and Hold feature
• RJ12 Splitter cable included

• Stylish, machined, anodized black bezel and slim enclosure
• High contrast Red LED display
• Large 0.4" (10mm) digits
• Slim design for flexible gauge mounting options
• Programmable to startup as an AFR or Lambda gauge
• Peak and Hold feature
• RJ12 Splitter cable included

• Blue digital AFR readout with large 0.4" (10mm) digits
• Slim 0.75" (19mm) design
• High contrast display visible even in direct sunlight
• RJ12 Splitter cable included

• Red digital AFR readout with large 0.4" (10mm) digits
• Slim 0.75" (19mm) design
• High contrast display visible even in direct sunlight
• RJ12 Splitter cable included