Woolich Racing Products

• USB D v3
• USB Cable
• Kawasaki Harness Type 1a
• Bin File Definition in the Woolich Racing Tuned software

The Race Tools package allows you to enable Quickshifter, Launch Control and Pit Speed Limiter in the Stock ECU.

The package includes:

• High quality strain gauge Quickshifter with digitally controlled pressure sensing that can be used in regular or race shift pattern.
• Shift rod for standard shift configuration*
• Kawasaki Race Tools Harness Type 2 which allows the quickshifter to be plugged into the bikes wiring harness**
• Race Tools Key to allow the use of the Race Tools on one ECU in the Woolich Racing Tuned software.

Quickshifter Kill times are configurable per gear with 3D maps allowing Kill Times to be set for the full range of TPS and RPM combinations. The quickshifter kills both fuel and ignition.

Launch Control allows you to configure Delay, Launch RPM, Ramp Time and Ramp RPM

Pit Speed Limiter allows you to set the RPM to limit the speed while riding through the pits.***

* Contact us after ordering if you have after-market rearsets or are using a race shift pattern and we will swap the shift rod for a generic rod that can be cut and tapped to the correct length.

** This harness uses the stock Exhaust Valve plugs on the bike's harness, the stock Exhaust Valve should be removed from the bike and disabled in our software

*** Pit Speed Limiter harness sold separately

• IAP Fuel Maps
• TPS Fuel Maps
• Ignition Timing Maps
• Secondary Throttle Plate (STP) Opening Maps
• Secondary Throttle Plate (STP) Closing Maps
• Injector Balance Map/s
• Exhaust Valve Opening Maps
• Ram Air Compensation Map/s
• RPM Limiter
• Fan Temperature
• Quickshifter - (Requires Race Tools)
• Launch Control - (Requires Race Tools)
• Pit Lane Limiter - (Requires Race Tools)
• Race Shift Pattern Sensor Configuration - (Requires Race Tools)
• Disable Stock O2 Sensor
• Disable Deceleration Fuel Cut
• Disable Exhaust Valve
• Disable PAIR Valve / AIS
• Disable Tip Over Sensor (TOS)
• ECU Mode
• Engine Data - View Live Engine Data
• Woolich Racing AutoTune - (Requires Applicable LogBox + Zeitronix Package)
• Diagnostics: Read and Clear Fault Codes - (Requires Applicable V3 Interface)

• 21175-0220
• 21175-0221
• 21175-0221 CJ76KPU0
• 21175-0221 CMA0KPU0
• 21175-0247
• 21175-0250
• 21175-0354 8J80KPE0
• 21175-0354 CMA0KPE0
• 21175-0355 8J80KPS0
• 21175-0355 CMA0KPS0
• 21175-0355 CMA0KPS0
• 21175-0356 8J80KPB0
• 21175-0356 CMA0KPB0

• Twin RJ12 cable to connect Zeitronix to Log Box
• Ducati Power Harness 1 & 2
• x O2 Stainless Steel Bung
• Adhesive Velcro for attaching ZT-3 to bike.

• Twin RJ12 cable to connect Zeitronix to Log Box
• Ducati  Power Harness 1 & 2
• 2  x O2 TITANIUM Bungs
  
• Adhesive Velcro for attaching ZT-3 to bike.

• RJ12 cable for connecting ZT-3 to Woolich Racing Products
• Kawasaki Power Harness Type 1
• O2 Stainless Steel Bung
  
• Adhesive Velcro for attaching ZT-3 to bike.

• RJ12 cable for connecting ZT-3 to Woolich Racing Products
• Kawasaki Power Harnes Type 2
  
• O2 Stainless Steel Bung
  
• Adhesive Velcro for attaching ZT-3 to bike.

• RJ12 cable for connecting ZT-4 to Woolich Racing Products
• KTM Power Harness Type 1
• 2 x O2 Stainless Steel Bung
  
• Adhesive Velcro for attaching ZT-4 to bike.

• RJ12 cable for connecting ZT-3 to Woolich Racing Products
• Suzuki Power Harness
  
• O2 Stainless Steel Bung
  
• Adhesive Velcro for attaching ZT-3 to bike.

• Wideband O2 sensor bung (stainless Steel)
  
• Wideband O2 sensor bung (Titanium)
• Tuning Shop Power Harness (type 1)
  
• RJ12 cables for connecting ZT-3 to Woolich Racing Products - 1 x small, 1 x large
  
• 2 x Narrow band bungs
  

• RJ12 cable for connecting ZT-3 to Woolich Racing Products
• Yamaha Power Harness
  
• O2 Stainless Steel Bung
  
• Adhesive Velcro for attaching ZT-3 to bike.

• Stylish, machined, anodized black bezel and slim enclosure
• High contrast Blue LED display
• Large 0.4" (10mm) digits
• Slim design for flexible gauge mounting options
• Programmable to startup as an AFR or Lambda gauge
• Peak and Hold feature
• RJ12 Splitter cable included

• Stylish, machined, anodized black bezel and slim enclosure
• High contrast Red LED display
• Large 0.4" (10mm) digits
• Slim design for flexible gauge mounting options
• Programmable to startup as an AFR or Lambda gauge
• Peak and Hold feature
• RJ12 Splitter cable included

• Blue digital AFR readout with large 0.4" (10mm) digits
• Slim 0.75" (19mm) design
• High contrast display visible even in direct sunlight
• RJ12 Splitter cable included

• Red digital AFR readout with large 0.4" (10mm) digits
• Slim 0.75" (19mm) design
• High contrast display visible even in direct sunlight
• RJ12 Splitter cable included