Woolich Racing Products

• Log Box M v3
• USB Cable
• On board 2GB micro SD card
• Kawasaki Harness Type 13a
• Bin File Definitions in Woolich Racing Tuned Software
• Zeitronix ZT-3 Wideband O2 Controller
• Zeitronix Wideband O2 Sensor (3 foot cable)

The Race Tools package allows you to add Autoblipper, Quickshifter, Pit Speed Limiter, Engine Warm Up and Launch Control to the Stock ECU.

The package includes:

• High quality dual direction strain gauge Quickshifter with digitally controlled pressure sensing that can be used in regular or race shift pattern.
• Shift rod for standard shift configuration*
• Kawasaki Race Tools Type 5 which allows the quickshifter to be plugged into the bikes wiring harness**
• Race Tools Key to allow the use of the Race Tools on one ECU in the Woolich Racing Tuned software.

Quickshifter Kill times are configurable per gear with 3D maps allowing Kill Times to be set for the full range of TPS and RPM combinations. 

Autoblipper Opening and Target maps are fully configurable per gear.

Pit Speed Limiter RPM can be configured.**

Launch Control allows you to configure Delay, Launch RPM and Hold Speed.

Engine Warm up parameters are fully configurable. **

* Contact us after ordering if you have after-market rearsets or are using a race shift pattern and we will swap the shift rod for a generic rod that can be cut and tapped to the correct length.

** The Pit Speed Limiter and Engine Warm Up requires the purchase of an additional Pit Speed Limiter Harness.

This item is for the Race Tools Key Only, it allows you to enable Woolich Racing Race Tools using the stock Shift Sensor. No Hardware is included with this item.

The Race Tools package allows you to add Autoblipper, Quickshifter, Pit Speed Limiter, Engine Warm Up and Launch Control to the Stock ECU.

Quickshifter Kill times are configurable per gear with 3D maps allowing Kill Times to be set for the full range of TPS and RPM combinations. 

Autoblipper Opening and Target maps are fully configurable per gear.

Pit Speed Limiter RPM can be configured.**

Launch Control allows you to configure Delay, Launch RPM and Hold Speed.

Engine Warm up parameters are fully configurable. **

* Contact us after ordering if you have after-market rearsets or are using a race shift pattern and we will swap the shift rod for a generic rod that can be cut and tapped to the correct length.

** This harness uses the stock exhaust valve plugs on the bike's harness, the stock exhaust valve should be removed from the bike and disabled in the WRT software

** The Pit Speed Limiter and Engine Warm Up, requires the purchase of an additional Pit Speed Limiter Harness.

• IAP Fuel Maps
• TPS Fuel Maps
• Ignition Timing Maps
• Ignition Dwell Map/s
• Electronic Throttle Valve (ETV) Maps
• Fuel Trim Map/s
• Injector Balance Map/s
• Intake Flap Opening Maps
• Exhaust Valve Opening Maps
• RPM Limiter
• Disable Stock O2 Sensor
• Disable Deceleration Fuel Cut
• Disable Exhaust Valve
• Diagnostics - Read and Clear Fault Codes
• Disable Top Speed Limiter
• Engine Braking Control Maps
• Wheelie Control Maps
• Engine Data - View Live Engine Data
• Woolich Racing AutoTune - (Requires Applicable LogBox + Zeitronix Package)
• Diagnostics: Read and Clear Fault Codes - (Requires Applicable V3 Interface)

• 21175-1646
• 21175-1656
• 21175-1662
• 21175-1668
• 21175-1685
• 21175-1702

• IAP Fuel Maps
• TPS Fuel Maps
• Ignition Timing Maps
• Ignition Dwell Map/s
• Electronic Throttle Valve (ETV) Maps
• Fuel Trim Map/s
• Intake Flap Opening Maps
• Exhaust Valve Opening Maps
• Idle RPM
• RPM Limiter
• Fan Temperature
• Quickshifter Ignition Cut Time
• Race Shift Pattern Sensor Configuration
• Disable Evap / Purge Valve
• Disable Stock O2 Sensor
• Disable Deceleration Fuel Cut
• Disable Exhaust Valve
• Disable Intake Flap
• Disable PAIR Valve / AIS
• Disable Top Speed Limiter
• Disable Acceleration Fuel Compensation
• Engine Braking Control Maps
• Enable Race Dash
• Tyre Circumference
• Engine Data - View Live Engine Data
• Woolich Racing AutoTune - (Requires Applicable LogBox + Zeitronix Package)
• Diagnostics: Read and Clear Fault Codes - (Requires Applicable V3 Interface)

• 21175-1268 FG1981B
• 21175-1270 FG1983B
• 21175-1271 FG1982B
• 21175-1274 FG1984B
• 21175-1275 FG1990B
• 21175-1276 FG1987B
• 21175-1308 FG1986B
• 21175-1434 FG3283C
• 21175-1434 RG3283C
• 21175-1435 FG3282C
• 21175-1435 RG3282C
• 21175-1436 FG3281C
• 21175-1436 RG3281C
• 21175-1438 RG3285C
• 21175-1440 FG3289C
• 21175-1440 RG3289C

• RJ12 cable for connecting ZT-3 to Woolich Racing Products
• Kawasaki Power Harness Type 1
• O2 Stainless Steel Bung
  
• Adhesive Velcro for attaching ZT-3 to bike.

• Twin RJ12 cable to connect Zeitronix to Log Box
• Ducati Power Harness 1 & 2
• x O2 Stainless Steel Bung
• Adhesive Velcro for attaching ZT-3 to bike.

• Twin RJ12 cable to connect Zeitronix to Log Box
• Ducati  Power Harness 1 & 2
• 2  x O2 TITANIUM Bungs
  
• Adhesive Velcro for attaching ZT-3 to bike.

• RJ12 cable for connecting ZT-3 to Woolich Racing Products
• Kawasaki Power Harness Type 1
• O2 Stainless Steel Bung
  
• Adhesive Velcro for attaching ZT-3 to bike.

• RJ12 cable for connecting ZT-3 to Woolich Racing Products
• Kawasaki Power Harnes Type 2
  
• O2 Stainless Steel Bung
  
• Adhesive Velcro for attaching ZT-3 to bike.

• RJ12 cable for connecting ZT-4 to Woolich Racing Products
• KTM Power Harness Type 1
• 2 x O2 Stainless Steel Bung
  
• Adhesive Velcro for attaching ZT-4 to bike.

• RJ12 cable for connecting ZT-3 to Woolich Racing Products
• Suzuki Power Harness
  
• O2 Stainless Steel Bung
  
• Adhesive Velcro for attaching ZT-3 to bike.

• Wideband O2 sensor bung (stainless Steel)
  
• Wideband O2 sensor bung (Titanium)
• Tuning Shop Power Harness (type 1)
  
• RJ12 cables for connecting ZT-3 to Woolich Racing Products - 1 x small, 1 x large
  
• 2 x Narrow band bungs
  

• RJ12 cable for connecting ZT-3 to Woolich Racing Products
• Yamaha Power Harness
  
• O2 Stainless Steel Bung
  
• Adhesive Velcro for attaching ZT-3 to bike.

• Stylish, machined, anodized black bezel and slim enclosure
• High contrast Blue LED display
• Large 0.4" (10mm) digits
• Slim design for flexible gauge mounting options
• Programmable to startup as an AFR or Lambda gauge
• Peak and Hold feature
• RJ12 Splitter cable included

• Stylish, machined, anodized black bezel and slim enclosure
• High contrast Red LED display
• Large 0.4" (10mm) digits
• Slim design for flexible gauge mounting options
• Programmable to startup as an AFR or Lambda gauge
• Peak and Hold feature
• RJ12 Splitter cable included

• Blue digital AFR readout with large 0.4" (10mm) digits
• Slim 0.75" (19mm) design
• High contrast display visible even in direct sunlight
• RJ12 Splitter cable included

• Red digital AFR readout with large 0.4" (10mm) digits
• Slim 0.75" (19mm) design
• High contrast display visible even in direct sunlight
• RJ12 Splitter cable included