Tune your bike to the limit with our advanced ECU Flashing products for Kawasaki, Honda, Suzuki, Ducati and Yamaha motorcycles.
Woolich Racing - Tune your bike to the limit
CONTACT US

Testing the M-Duc USB / LOGBOX v3 Interface

On the "Tools" menu there is an item for "Test Interface", this allows the basic interface communications to be tested.

Note: The following only applies to the M-Duc USB / LOGBOX v3 Interfaces.

To Test Flashing Mode 

1. Ensure the interface is NOT plugged into an ECU.

2. Ensure you have the Interface powered with 12v connected to pin 5 and Ground connected to pin 8 on the Interface.

If you have a bench harness to suit the Mitsubishi Interface you can connect the 8 pin molex connector and power supply.


If you only have a power supply you can connect to the interface as below.


3. Connect the USB cable from the Interface to the computer.

4. Move the mode switch on the interface to the right hand side position to the Read / Write mode. 

    Note: The v3 interface may not show the Red led until Test interface has started.

5. Turn on Power Supply.

6. Open the Woolich Racing Tuned Software, go to "Tools" then to "Test Interface".

7. Click Test Interface.




Voltage Tests on M-Duc v3 Interfaces ONLY

Use a  multimeter in a DC voltage setting to perform the following tests.

1. Connect the USB cable from the Interface to the computer.

2. Move the mode switch on the interface to the right hand side position to the Read / Write mode.

3. Connect the Interface with a 12v power supply either by the bike ignition with an on bike harnesses or with the 12v power supply using a bench harnesses connected to the 8 pin molex connector. Ensure the interface is NOT plugged into an ECU. 

4. Open the Woolich Racing Tuned Software.

5. Select and open a Bin file that uses a M-Duc v3 Interface.

6. Click Read or Write ECU and measure the voltage between pin 3 and pin 8 on the interface, this should be 11.5v-13.5v when in flashing mode (Red LED on).

7. Click Read or Write ECU and measure the voltage between pin 4 and pin 8 on the interface, this should be 14.0v - 16.0v when in flashing mode (Red LED on).


The plug pin out above is the 8 pin Molex plug on the Interface



If any of the test fail, please Contact Us


Was this helpful?
Back To Support Center

 
OUR PRODUCTS SUPPORT OUR COMPANY  
Suzuki ECU Flashing
Kawasaki ECU Flashing
Honda ECU Flashing
Yamaha ECU Flashing
Ducati ECU Flashing
Woolich Racing Merchandise
What Harness for Bike?
What Bike uses Harness?
Woolich Racing Tuned (WRT) software
Woolich Racing MapShare
USB D (Denso)
Log Box D (Denso)
Log Box Pro D (Denso)
USB M (Mitsubishi)
Log Box M (Mitsubishi)
Log Box Pro M (Mitsubishi)
Zeitronix Wideband O2 Products
Tuning Shops and Dealers
Support Center
Support Tickets
Video Tutorials
User Guides and Installation Instructions
COM Port Drivers
Woolich Racing Forums
User Support
Contact Us
About Us
Official Technical Partner WorldSBK
Electronic Mapping - Plug and Play Performance
Woolich Racing News
Testimonials
Terms and Conditions
Privacy Policy
Woolich Racing page on facebook
Woolich Racing on YouTube.com
Woolich Racing Products are Intended for RACE USE on CLOSED CIRCUIT ONLY

© Woolich Racing and www.WoolichRacing.com, 2011-2017. Unauthorized use or duplication of any of the material on this website without express and written permission from this website’s author and owner is strictly prohibited. Excerpts and links may be used, provided that full and clear credit is given to Woolich Racing and www.WoolichRacing.com with appropriate and specific direction to the original content.